Comtech EF Data LPOD Spezifikationen Seite 132
- Seite / 218
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
LPOD C-, X-, or Ku-Band Outdoor Amplifier / Block Up Converter (BUC) MN-LPOD
Serial-based Remote Product Management Revision 10
5–32
Parameter Type
Command
(Instruction
Code and
Qualifier)
Arguments
for Command
or Response
to Query
Description of Arguments
(Note that all arguments are printable ASCII characters)
Response to
Command
(Target to
Controller)
Query
(Instruction
Code and
Qualifier)
Response to Query
(Target to
Controller)
Remote Baud
Rate
SBR=
4 bytes
Command or Query.
Sets or returns the remote baud rate in the form xxxx, where:
2400 = 2400 baud
4800 = 4800 baud
9600 = 9600 baud (default value)
19K2 = 19200 baud
38K4 = 38400 baud
Note: When changing baud rates remotely the response to the command will be returned using the same baud
rate as that used to send the command.
Examples: <1/SBR=9600’cr’
>0001/SBR=9600’cr’’lf’
<1/SBR?’cr’
>0001/SBR=09600’cr’’lf’
SBR=
SBR?
SBR*
SBR?
SBR=xxxx
(See Description of
Arguments)
Switch Bias Tee
SBT=
1 byte
numeric
Command or Query.
Sets or returns switching of the bias tee into the through state or into the off state, in the form x, where:
0 = Off State (mute LNB) (default value)
1 = Through State (unmute LNB)
Notes:
1) The bias tee provides a means of muting the LNB. The SBT state will be controlled by the amplifier mute
state while running in redundant mode, but while the unit is not in redundant mode the bias tee may be set
independently of the amplifier mute state.
2) To send this command the unit must have the bias tee option installed otherwise a mode error will result. A
mode error will also result if this command is sent while the unit is running in redundant mode.
Example: <1/SBT=1
SBT=
SBT?
SBT*
SBT?
SBT=x
(See Description of
Arguments)
Set FSK Address
SFA=
2 bytes,
numeric
Command or Query.
Sets or returns the FSK Address in the form xx, where:
xx=01-15
Default value: 01
Example: <1/SFA=01’cr’
>0001/SFA=’cr’’lf’
SFA =
SFA?
SFA*
SFA?
SFA=xx
(See Description of
Arguments)
Summary Fault
Status
E
N/A
1 byte
Query only.
Returns the condition of the summary fault relay in the form x, where:
0 = Not Faulted (SumFLT_COM J6 pin K is not connected to SumFLT_NC J6 pin M)
1 = Faulted (SumFLT_COM J6 pin K is connected to SumFLT_NC J6 pin M)
Example: <1/SFS?
>0001/SFS=0’cr’’lf’
SFS=
SFS?
SFS=x
(See Description of
Arguments)
- Revision 10 1
- Part Number MN-LPOD 3
- Revision 10 3
- TABLE OF CONTENTS 5
- vii 9
- FIGURES 10
- PREFACE 13
- Electrical Safety Notice 14
- Product Support 15
- Preface Revision 10 16
- Chapter 1. INTRODUCTION 19
- 1.2 Functional Description 20
- 1.3 Features 20
- 1.3.7 Optional LNB Support 21
- 1.4 Theory of Operation 22
- 1.4.1 SSPA Block Diagrams 22
- 1.4.2 SSPA Module 23
- 1.4.3 Cooling System 24
- 1.4.5 LNB Operation 24
- 1.4.6 Power Supply 24
- BUC C, Ku, X LO Frequencies 25
- 1.5.1 Characteristics 26
- 1.5.4 Environmental 28
- 1.5.5 Physical 28
- 1.6 Dimensional Envelopes 30
- Introduction Revision 10 31
- Chapter 2. SYSTEM 41
- CONNECTIONS, INSTALLATION 41
- STARTUP 41
- 2.3 Interface Connectors 44
- Control Port) 48
- 2.3.8 Ground Connector 49
- 2.5 Power-up the LPOD 50
- Chapter 3. UPDATING FIRMWARE 55
- Chapter 4. ETHERNET-BASED 65
- REMOTE PRODUCT 65
- 4.3 SNMP Interface 66
- 4.3.3 SNMP Traps 67
- 4.4 Telnet Interface 70
- Enter the LPOD’s 71
- 4.5.2 User Login 73
- 4.5.3.1 Menu Tree 74
- 4.5.3.2 Page Navigation 74
- 4.5.3.3 Page Sections 74
- 4.5.3.4 Action Buttons 75
- 4.5.3.5 Drop-down Lists 75
- 4.5.3.6 Text or Data Entry 75
- 4.5.4.1 Home Pages 76
- 4.5.4.1.1 Home 76
- 4.5.4.1.2 Home 77
- 4.5.4.1.3 Home 78
- 4.5.4.2 Admin Pages 79
- 4.5.4.2.1 Admin 79
- Webpage Timeout 80
- 4.5.4.2.2 Admin 81
- 4.5.4.3 Config Pages 82
- 4.5.4.3.2 Config 84
- 4.5.4.3.3 Config 85
- Redundancy 87
- Online Status 87
- Force Online 87
- 4.5.4.4 Status Pages 88
- 4.5.4.4.1 Status 88
- 4.5.4.4.2 Status 89
- 4.5.4.4.3 Status 90
- 4.5.4.4.4 Status 91
- Alarm Mask 92
- Statistics Configuration 94
- 4.5.4.4.6 Status 95
- Control Bar and Refresh Tab 96
- Temperature Graph 97
- Power Graph 97
- LNB Current Graph 98
- Amplifier Status Graph 98
- Mute State Graph 98
- Online Status Graph 99
- Minimum Fan Speed Graph 99
- MANAGEMENT 101
- 5.2.2 Attenuator Control 102
- 5.2.3 Mute Control 102
- 5.2.4 Faults 102
- 5.2.5 Power Detector 104
- 5.2.6 Some Common Commands 104
- 5.2.7 End-of-Life Commands 104
- 5.1.1 EIA-485 105
- 5.1.2 EIA-232 106
- 5.1.3 Basic Protocol 106
- 5.1.4 Packet Structure 106
- 5.1.4.1 Start of Packet 107
- 5.1.4.2 Target Address 107
- 5.1.4.3 Address Delimiter 107
- 5.1.4.4 Instruction Code 108
- 5.1.4.7 End of Packet 109
- Appendix A. 1:1 REDUNDANCY 137
- Appendix A Revision 10 138
- A.5.1 Common Kit Examples 146
- BLANK PAGE 151
- Appendix B. CABLE DRAWINGS 193
- B.2 Control and Data Cables 194
- Appendix B Revision 10 195
- B.3 RF Cables 202
- B.3.1 RF Cable (Type ‘N’) 203
- Appendix C. MAINTENANCE 205
- Appendix C Revision 10 206
- 212
- 480 • 333 • 2200 PHONE 218
- • 333 • 2161 FAX 218
Verwandte Produkte und Handbücher für Audioverstärker Comtech EF Data LPOD
(60 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.240 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern