Comtech EF Data UT-4514F Spezifikationen Seite 48
- Seite / 162
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
UT-4500-A Series Upconverters Revision 1
Installation MN-UT4500A
2–6
2.2.2 Installing the Bearingless Rack Slide Sets
If the converter is to be mounted on slides, install the provided bearingless rack slide set into
the rack cabinet, and onto the sides of the UT-4500-A. Use the hardware provided with the slide
set that is determined to be appropriate for installation:
CEFD Part Number Description
FP/SL0006 Bearingless Rack Slide Set – 26”
FP/SL0008 Bearingless Rack Slide Set – 24”
Per Figure 2-4, install any of these optional bearingless rack slide sets as follows:
Step Procedure
1
Using the provided mounting hardware, install one slide onto each side of the UT-
4500-A chassis.
2
Using the provided mounting hardware, install the slide rail components into each
side of the rack cabinet.
3
Mount the unit into the equipment rack, ensuring that the slides properly engage
the cabinet-mounted slide rails.
4
Slide the converter into the rack cabinet until the front panel’s back surfaces
abut the rack cabinet’s front mounting rails.
5
Secure the converter to the rack cabinet front mounting rails using four user-
provided screws installed through the front panel mounting slots.
Figure 2-4. Optional Bearingless Rack Slide Installation (FP/SL000X)
- UT-4500-A Series 1
- TABLE OF CONTENTS 5
- FIGURES 12
- PREFACE 15
- Metric Conversion 16
- Safety and Compliance 17
- Electrical Installation 17
- Operating Environment 17
- (2004/108/EC) 18
- Preface MN-UT4500A 19
- Warranty Policy 20
- Limitations of Warranty 20
- Exclusive Remedies 21
- Getting Help 22
- Contacting Comtech EF Data 22
- Chapter 1. INTRODUCTION 25
- 1.2 Functional Description 26
- 1.2.1 Applications 27
- 1.2.2 RF Signal Conversion 28
- 1.2.3 Monitor & Control 28
- 1.3 Upconverter Features 29
- 1.3.1 Physical Description 29
- 1.3.2 Dimensional Envelope 30
- 1.3.3.1 Front Panel 31
- 1.3.3.2 Rear Panel 31
- Introduction MN-UT4500A 32
- Chapter 2. INSTALLATION 43
- Installation MN-UT4500A 44
- 2.4 Connect External Cables 49
- Chapter 3. REAR PANEL 51
- CONNECTORS 51
- 3.3 Cable Connections 59
- Module (TSM-XX) 60
- Chapter 4. UPDATING FIRMWARE 63
- Chapter 5. FRONT PANEL 69
- OPERATION 69
- 5.1.2 LED Indicators 70
- 5.1.3 Keypad 71
- 5.2 2BOpening Screen 72
- 5.3 Main Menu 72
- 5.3.1.1 CONFIG: OUTPUT 73
- ▲ ▼ arrow keys 75
- ▲ ▼ arrow keys to edit 76
- 5.3.1.3 CONFIG: REDUNDANCY 77
- 5.3.1.5 CONFIG: COLDSTART 79
- 5.3.2 MONITOR 80
- 5.3.3 FAULTS 80
- 5.3.3.1 FAULTS: CURRENT 80
- 5.3.4 PRE-SELECTS 82
- 5.3.4.1 PRE-SELECTS: LOAD 82
- 5.3.4.3 PRE-SELECTS: CLEAR 83
- 5.3.5 UTILITY 83
- 5.3.5.5 UTILITY: SLOPE 85
- 5.3.5.6 UTILITY: LAMP-TEST 85
- 5.3.5.7 UTILITY: FIRMWARE 85
- Chapter 6. ETHERNET-BASED 87
- REMOTE PRODUCT 87
- MANAGEMENT 87
- 6.2 SNMP Interface 88
- 6.2.3 SNMP Traps 89
- 6.3 Telnet Interface 90
- 6.4.2 User Login 92
- 6.4.3.1 Navigation 93
- 6.4.3.2 Page Sections 93
- 6.4.3.3 Action Buttons 93
- 6.4.3.4 Drop-down lists 94
- 6.4.3.5 Text or Data Entry 94
- 6.4.5.1 Home Pages 95
- 6.4.5.1.1 Home 95
- 6.4.5.1.2 Home 96
- 6.4.5.1.3 Home 97
- 6.4.5.2 Admin Pages 98
- 6.4.5.2.1 Admin 98
- Webpage Timeout 99
- 6.4.5.2.2 Admin 100
- 6.4.5.3 Config Pages 101
- 6.4.5.3.2 Config 103
- Pre-Selects 104
- Load Pre-Select 104
- 6.4.5.3.4 Config 105
- Perform Soft Reboot 106
- Part Number (read-only) 106
- 6.4.5.4 Status Pages 108
- 6.4.5.4.1 Status 108
- 6.4.5.4.2 Status 109
- Appendix A. REMOTE CONTROL 111
- A.2.2 TIA/EIA-232 (RS-232) 112
- A.2.3 Ethernet (100BASE-TX) 112
- A.3 Access Methods 112
- A.3.1 Direct Access 112
- A.3.2 Indirect Access 113
- A.4 Addresses 113
- A.4.1 Physical Address 113
- A.4.2 Virtual Address 113
- Appendix A MN-UT4500A 114
- A.6.4 Confirmation Response 116
- A.6.5 Error Response 116
- A.6.6 End of Message 116
- A.6.6.1 Command Ending 116
- A.6.6.2 Response Ending 116
- A.7.1 Utility Commands 117
- A.7.1.1 Time 117
- A.7.1.2 Date 117
- A.7.1.7 IP Address 119
- A.7.1.8 IP Gateway 119
- A.7.1.9 Physical Address 119
- A.7.1.10 Baud Rate 120
- A.7.1.11 LCD Contrast 120
- A.7.1.12 LCD Brightness 120
- A.7.1.13 Screen Saver Mode 120
- A.7.1.15 VFD Brightness 121
- A.7.1.18 Equipment Type 122
- A.7.1.19 Part Number 122
- A.7.1.22 Firmware Image 123
- A.7.1.24 Force Reboot 124
- A.7.2.1 Frequency 125
- A.7.2.2 Attenuator 125
- A.7.2.3 Cold Start 125
- A.7.2.4 Mute 126
- A.7.2.5 Carrier Mute Mode 126
- A.7.2.6 Redundant Mute Mode 126
- A.7.2.7 Auto Fault Recovery 127
- A.7.2.8 Program Preset 127
- A.7.2.9 Display All Presets 127
- A.7.3 Modes 129
- A.7.3.1 Redundant Mode 129
- A.7.3.3 Backup Mode 130
- A.7.4 Status Commands 131
- A.7.4.2 Maintenance Status 131
- A.7.4.3 Utility Status 132
- A.7.4.4 Alarm Status 132
- A.7.5 Stored Alarms 136
- A.7.5.1 Total Stored Alarms 136
- A.7.5.3 List All Alarms 136
- A.7.6 Error Processing 137
- A.7.6.1 General Errors 137
- A.7.6.3 Mode Errors 137
- A.7.6.4 Time-Outs 137
- A.7.7 Command Summaries 138
- Appendix B. REDUNDANT 141
- SYSTEM OPERATION 141
- B.2 Backup Upconverter 142
- B.2.1 High Speed Bus (HSB) 142
- B.2.2 Detachable Modules 142
- Appendix B MN-UT4500A 143
- TSM-XX Installed 145
- Interface 153
- B.4.3 Offset Adjustment 154
- Appendix C. MAINTENANCE AND 157
- TROUBLESHOOTING 157
- Appendix C MN-UT4500A 158
- C.2.3.3 RF Converter Module 159
- C.2.3.7 Temperature Fault 159
- C.2.4 Converter I/O Modules 160
- C.3 Spares 160
- METRIC CONVERSIONS 161
- Units of Length 161
- Temperature Conversions 161
- Units of Weight 161
- 480 • 333 • 2200 PHONE 162
- • 333 • 2161 FAX 162
Verwandte Produkte und Handbücher für Nein Comtech EF Data UT-4514F
Nein Comtech EF Data MBT-4000B Spezifikationen
(88 Seiten)
(88 Seiten)
Nein Comtech EF Data CIC-50 Spezifikationen
(38 Seiten)
(38 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern