Comtech EF Data KST-2000A Spezifikationen Seite 118
- Seite / 182
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Ku-Band Satellite Transceiver Revision 9
Terminal Mode Commands MN/KST2000AB.IOM
B–8
B.3.3 Reset Commands
Reset
Redundancy
Faults
Command
Response
<add/RRF_’cr’
>add/RRF_’cr’’lf’]
Note: Resets/clears any detected redundancy faults. This command
is intended to be used with a redundant system that was decided to
be disassembled into a single-thread system. Improper disassembly
will cause the M&C to report certain redundancy faults. By
supplying this command the user will be notifying the M&C that
the system will no longer be a redundant system and those faults
should be reset.
Up Converter
Latched Fault
Reset
Command
Response
Status
Response
<add/ULR_RESET’cr’
>add/ULR_RESET’cr’’lf’]
<add/ULR_’cr’
>add/ULR_’cr’
LSSYN_xxx’cr’
LKSYN_xxx’cr’’lf’]
Note: Resets/clears any detected faults (Reset occurs on power up).
Latched S-Band Synthesizer Lock Detect (OK/FLT)
Latched Ku-Band Synthesizer Lock Detect (OK/FLT)
Down Converter
Latched Fault
Reset
Command
Response
Status
Response
<add/DLR_RESET’cr’
>add/DLR_RESET’cr’’lf’]
<add/DLR_’cr’
>add/DLR_’cr’
LLSYN_xxx’cr’
LKSYN_xxx’cr’’lf’]
Note: Resets/clears any detected faults (Reset occurs on power up).
Latched L-Band Synthesizer Lock Detect (OK/FLT)
Latched Ku-Band Synthesizer Lock Detect (OK/FLT)
M&C Soft
Reset
Command
Response
<add/SRM_’cr’
Note: All current variables are retained, as system restarts.
M&C Hard
Reset
Command
Response
<add/HRM_’cr’
Note: All current variables will be updated to default values.
UC Automatic
Gain Control
Command
Response
<add/UAGC_xxx’cr’
>add/UAGC_xxx’cr’’lf’]
Where: xxx = ON/OFF
Default = OFF on “cold start” or “hard reset”UAGC will be set to
the last programmed state on subsequent power cycles.On will
enable UC automatic gain control.
OFF will disable UC automatic gain control.
Note: Disabling UAGC will cause the UC attenuation to be
displayed as an integer (without a decimal point).
B.3.4 Status Commands/Responses
System
Configuration
Status
Command
Response
<add/OS_’cr’
>add/OS_’cr’
UCF_nnnnn.n’cr’
DCF_nnnnn.n’cr’
RF_xxx’cr’
UCA_nn.n’cr’
DCA_nn.n’cr’
SEL_n’cr’’lf’]
Where:
nnnnn.n = 13750.0 to 14500.0 MHz
nnnnn.n = 10950.0 to 12750.0 MHz
xxx = ON, WRM or OFF
nn.n = 0.0 to 25.0 dB
nn.n = 0.0 to 20.0 dB
n = 1, 2, 3, or None
The converter configuration status command causes a
block of data to be returned by the addressed KST-
2000A/B. The block of data reflects the current
configuration status.
System Fault
Status
Command
Response
<add/FS_’cr’
>add/FS_’cr’
US_xxx’cr’
HS_xxx’cr’
DS_xxx’cr’
RS_xxx’cr’
AGS_xxx’cr’
LS_xxx’cr’
CES_xxx’cr’’lf’]
Up Converter Faults (OK/FLT)
HPA Faults (OK/FLT)
Down Converter Faults (OK/FLT)
Reference Faults (OK/FLT)
AGC Faults (OK/FLT)
LNA Faults (OK/FLT)
Common Equipment Faults (OK/FLT)
- Ku-Band Satellite Transceive 1
- Installation and O 1
- KST-2000A/B 3
- Customer Service 4
- Table of Contents 5
- Figures 9
- Preface MN/KST2000AB.IOM 10
- Preface 11
- Related Documents 12
- Warranty Policy 13
- Chapter 1. INTRODUCTION 15
- 1.1 Description 16
- 1.1.3 Areas of Operation: 17
- 1.1.4 Features 18
- 1.1.4.2 Other Features 19
- Ku-Band & 20
- DC Power 20
- DC Power & 22
- 10 MHz Ref 22
- 1.1.7 Redundant System 23
- 1.2 Specifications 24
- to + 140°F) 26
- Notes: 27
- Chapter 2. INSTALLATION 29
- . (see Note) 30
- 2.3. Description of Options 31
- 2.4. Electrical Connections 32
- 2.4.1. Converter Unit 32
- 2.4.1.9 HPA Connector (J8) 38
- 2.4.2. Data SSPAs 41
- 2.4.3. LNA Connections 48
- 2.4.4. LNB Connections 48
- Chapter 3. OPERATION 49
- 3.1.1 Uplink Setup 51
- 3.1.2 Downlink Setup 52
- (2 places) 55
- PL/8085-2 55
- 3.4 Connector Descriptions 58
- 3.4.7 Other Connectors 63
- 3.5 Indicators Description 63
- Unit A Unit B 65
- 3.7 Reference Oscillator 70
- • Fault relays • ROM/RAM 72
- 3.11.1 Operation 77
- AND ISOLATION 81
- Chapter 4. FAULT INDICATION 81
- 4.2 Fault Isolation 82
- 4.3 Stored Faults 82
- Chapter 5. KEYPAD / DISPLAY 85
- 5.3 The Menu Structure 89
- 5.3.1 Configuration 90
- ] or [ X] to move the 91
- 5.3.2 Monitor 93
- 5.3.3 Faults 94
- 5.3.4 Utility 97
- 5.3.5 System 98
- or [ X] arrow buttons 99
- 5.3.6 Redundancy 100
- Operation MN/KST2000AB.IOM 102
- Appendix A. EQUIPMENT 103
- OUTLINE DRAWINGS 103
- TOLERANCE: +/- .02 (0.5) 108
- 5.67 (143.8) 110
- 5.12 (130.0) 110
- 2.55 (65) 110
- 1.58 (40) 110
- Type “N” 110
- Appendix B. TERMINAL MODE 111
- COMMANDS 111
- B.2 Message Structure 112
- B.2.1 Start Character 112
- B.2.2 Device Address 112
- B.2.3 Command/Response 113
- B.2.3 End Character 114
- B.3.3 Reset Commands 118
- <add/HS_’cr’ 119
- >add/HS_’cr’ 119
- B.3.5 Stored Faults 121
- B.3.6 Miscellaneous 124
- B.4.1 External Fault Mode 126
- Appendix C. SINGLE-THREAD 127
- EQUIPMENT MOUNTING 127
- C.1 Tools Required 128
- C.2.1 Spar Arm Mount 129
- Figure C-2 131
- C.2.2 Pole Mount 132
- Flat fitting plate 133
- Pipe block 133
- C.3 SSPA Installation 136
- C.4 LNA Installation 139
- C.5 Cable Installation 140
- Appendix D. REDUNDANT 141
- D.1 Tools Required 142
- D.2.1 Spar Arm Mount 143
- D.2.2 Pole Mount 146
- D.3 1:1 SSPA Installation 150
- D.4 1:1 LNA Installation 151
- D.5 Cable Installation 151
- Appendix E. FSK REMOTE 153
- CONTROL COMMANDS 153
- E.2 Basic Protocol 154
- E.2.1 Packet Structure 155
- E.2.2 Start Of Packet 155
- E.2.3 Address 155
- E.2.4 Instruction Code 155
- E.2.6 Message Arguments 158
- E.2.7 End Of Packet 158
- E.3 Commands and Query 158
- 2W SSPA – Item D=BV1 171
- Glossary 177
- Ω kilo-ohms 178
- Glossary MN/KST2000AB.IOM 180
Verwandte Produkte und Handbücher für Nein Comtech EF Data KST-2000A
Nein Comtech EF Data UT-4514F Spezifikationen
(162 Seiten)
(162 Seiten)
Nein Comtech EF Data MBT-4000B Spezifikationen
(88 Seiten)
(88 Seiten)
Nein Comtech EF Data CIC-50 Spezifikationen
(38 Seiten)
(38 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern